Hydrate Ultra: instructional videos
Installing, maintaining and repairing yourself, explained step by step.
Knowledge base article
Installation
Drinking fountain installation
The Hydrate Ultra box contains:
- The Hydrate Ultra
- Manual
- Filter
- Cable and adapter
Unpack the product and remove the lid and filter holder. Connect the product to the power supply. Then remove the inner container and fill it with water. Pay attention to the max line. Then place the filter holder on top, insert the filter, and then the lid. Place the inner container back into the outer container.
Download the Pettadore app from your app store. Make sure your phone is connected to a 2.4 GHz network and click the “+” in the app. Then choose the correct product and follow the instructions in the app.
Tip: do not place the drinking fountain too close to the litter box or automatic feeder, as cats do not like that. Cats like to give everything its own space; a few meters apart is fine. You can also place multiple water stations around the house so that your cat comes across water more often.
Usage and tips
Usage and tips
The inner container of the Hydrate Ultra may yellow over time. This is caused by the UV light and is harmless.
You can easily remove the lid by placing your hands around the hole in the lid and pulling it towards you. The same applies to the filter holder.
You can reset the drinking fountain by inserting a paperclip into the hole on the front. Hold it there until the Wi-Fi light starts flashing.
In the app, you can see, among other things:
- TDS: the amount of particles in the water. This varies by region and water source. The reading may increase due to, for example, dust. If it is higher than usual, it is a sign to change the water.
- Water level: we recommend changing the water every 5 days. Indicate in the app that you have changed the water, and the app will start counting again.
- Reminders: replace the filters every 30 days and thoroughly clean the pump every 60 days.
You can set an operating period. This is the period during which the drinking fountain is turned off. We recommend leaving the drinking fountain on as much as possible. You can also dim the LED indicator at certain times, turn the drinking fountain off completely, view the version, change the name, and share your device in the app.
Drink tips
In the past, cats got a lot of moisture from their prey. Nowadays, most cats eat dry food and no longer hunt. That is why we recommend also giving wet food and ensuring your cat has easy access to water. You can do this by:
- Choose flowing, fresh water. A drinking fountain continuously refreshes the water. If you use a regular water bowl, wash it thoroughly twice a day.
- Place the water in a smart location. For example, along your cat's walking route, so they pass it often.
- Move the drinking fountain occasionally. This will pique your cat's curiosity.
- Keep it away from the litter box and food. Cats like to give everything its own space; a few meters apart is perfect.
Also check out our cheatsheet under "Downloads", with more than 100 tips for caring for your cat.
Maintenance
Maintenance service
Replace the filters in your Hydrate Ultra every 30 days and give it a major service every 60 days.
Important: never use soap. Cats do not like it and may stop drinking. Use only water and paper. If there is rust, you can use a little cleaning vinegar. Let the drinking fountain run for a while with the vinegar, then rinse thoroughly 3 or 4 times and dry everything so that the vinegar smell disappears.
First, remove the inner container from the outer container. Remove the lid and filter holder and pour out the water or temporarily store it somewhere else.
A slimy layer can form on the pump housing, the thread and the pump. Clean this. Wipe all parts thoroughly with paper: under the UV lamp, the pump housing, the cable, the tube and the silicone bed.
Then remove the pump housing. The older version of the Hydrate Ultra (1) requires pump stickers, the new version does not. You can see which version you have on the bottom of your device: on the Hydrate Ultra 1 it says “Hydrate Ultra”, on the Hydrate Ultra 2 it says “Hydrate Ultra 2”.
On the Hydrate Ultra 1, remove the pump sticker and thoroughly remove the glue residue. Open the pump by removing the covers. You will then see a rotor, which you remove with needle-nose pliers or tweezers. Cleaning everything is best done with a cotton swab.
Replace the clean rotor and put the covers back on. Press the tube completely against the pump. On the Hydrate Ultra 1, stick on a new pump sticker and place a new foam piece. Put the clean pump housing back on. Make sure the tube is not doubled over, as this can cause problems.
Then clean the filter holder and the lid with paper and water. Fill the inner container with water, place the filter holder with a new filter and put the lid on. Put the inner container back in the outer container.
You can find additional instructions in the app. Then indicate under “pump maintenance” that you have cleaned the drinking fountain and the filter. This way, the app keeps track of when the next service is needed.
Replace filters
A filter set consists of:
- 3 filters
- 3 pump stickers (only needed for the Hydrate Ultra 1)
- 3 foam pieces
We recommend replacing the filters every 30 days.
The pump stickers are needed for the older version of the Hydrate Ultra (1), but not for the new version. You can see which version you have on the bottom of your device: the Hydrate Ultra 1 says “Hydrate Ultra”, and the Hydrate Ultra 2 says “Hydrate Ultra 2”.
Remove the inner container from the outer container and pour out the water to make replacement easier. Remove the lid and the filter holder.
Remove the pump housing and replace the old pump foam with a new one. For the Hydrate Ultra 1, replace the sticker as well.
Then replace the pump housing. Put the filter holder back on the inner container and replace the large filter with a new one. Put the lid on and place the inner container back in the outer container.
You can find additional instructions in the app. Indicate there that you have replaced the filters so that the app can keep track of when it is time again.
Install new pump
Please note: first check that you have the correct pump. There are two versions of the Hydrate Ultra. The Hydrate Ultra 1 is the older version with a black pump, the Hydrate Ultra 2 is the new version with a white pump. You can see which version you have on the bottom of your device: the Hydrate Ultra 1 says “Hydrate Ultra”, the Hydrate Ultra 2 says “Hydrate Ultra 2”.
Here is how to install the new pump:
- Remove the inner container from the outer container, remove the lid and filter holder, and pour out the water.
- Remove the pump housing. Dry the pump thoroughly with paper, especially around the connection point. This must always remain dry.
- Disconnect the cable from the connectors and check the pins. If you see any corrosion, please contact our customer service.
- Is everything in order? Take the new pump, unscrew the loose wire, and connect the pump to the inner container cable. Both parts have a notch that allows you to snap them together. Screw everything tightly and press the tube firmly against the pump again.
- Replace the foam insert and put the pump housing back on the pump.
Do you have any questions? Please contact our customer service.
Troubleshooting
No water flow
Is no water or very little water coming out of your drinking fountain? This could be due to the following causes:
- Power supply: perhaps the device is not receiving a proper power supply. Check if your device is available in the app and if the light is on. If so, the power supply is not the problem.
- Dirty pump: remove the pump housing and the pump covers. Remove the rotor with needle-nose pliers or tweezers and clean the area with a cotton swab. Put everything back.
- Tube not properly attached: push the plastic tube completely onto the pump. Otherwise, it may fold over when replacing the housing, and no water will flow through.
- Blockages: check if anything is blocking the pump screen so that the pump can draw in water. Also check if the tube is clear so that the water can flow up.
Are you still having problems with the water flow? Then contact our customer service.
Drinking fountain makes noise
Is your Hydrate Ultra making a lot of noise? There are several solutions for this.
Is your Hydrate Ultra still new? Then wait a week. A new pump often needs time to break in, after which the noise usually disappears.
Is your Hydrate Ultra a bit older? Then first clean the pump thoroughly. A clean pump can pump the water more easily and often makes less noise. You can see how to clean the pump in the Maintenance video.
Noise is often caused by something obstructing the pump. The pump then has to work harder. Therefore, check:
- whether the plastic tube is pressed completely against the pump, so that it does not double up when you replace the pump housing;
- whether nothing is stuck in the foam;
- whether the pump is not touching the inner container.
The surface also makes a difference. The device has silicone feet and a silicone insert that dampen the noise. On a wooden table, the device sounds louder than on, for example, a concrete floor.
A drinking fountain on a hard floor normally makes about 40 to 50 decibels. You can measure this with a free app.
Are you still experiencing noise or do you need help? Then contact our customer service. They will ask you for a video and the number of decibels you measure.
Drinking fountain is making noise: check pump and parts
Does the noise persist? Here you can check the pump and the surrounding parts step by step.
Drinking fountain restarts and beeps
If your drinking fountain keeps restarting and beeping, it is often due to the power supply. It could also be that the connection points are wet.
First, try a different adapter. If that doesn't help, replace the cable.
Still not resolved? Then check the solder points on the bottom of the inner container. These should be dry and free of oxidation. If they are wet or oxidized, dry and clean them.
Finally, check the pins on the pump. These should also be dry and clean. If you see a lot of corrosion, please contact us.
Does your drinking fountain still restart and beep after doing this? Then please contact our customer service.
Cat does not want to drink
Use these tips to help your cat get used to the drinking fountain:
- Place the drinking fountain where the old water bowl used to be. That way, your cat will know where to go.
- Let your cat smell and feel the water. Cats rely less on sight and more on smell and touch.
- Play by the drinking fountain. Let your cat touch the water, for example by shining a laser pointer or another toy on it. This will help your cat realize it is water.
- Remove the old water bowls. Then your cat will naturally get used to the drinking fountain.
- Give it time. Give your cat at least two weeks to adjust. Cats can be stubborn and often need a little longer before something new becomes part of their routine.
Still have questions? Contact our customer service team.
Check pump
This is how you check if the pump is working properly. This will quickly show you whether you need to clean or replace the pump.
Check connectors
If the drinking fountain does not work or only works intermittently, check that the connectors are securely attached and clean.
Repair
Replace outdoor enclosure
Is the outer casing damaged? In this video, you'll see how to replace it.
Replace inner tray
This is how you remove the old inner tray and replace it with a new one.
Replace filter tray
The filter holder keeps the filter in place. Here you can see how to insert a new filter holder.
Replace drink tray
This is how you replace the drinking tray, the part your cat drinks from.
Replace pump
Is the pump no longer working, even after cleaning? Then you can replace it in a few steps with this video.
Replace pump cover
The pump cover fits over the pump. Here you can see how to remove it and install a new one.
Replace silicone tubing
Is the tube leaking or not fitted properly anymore? In this video, you'll see how to install a new silicone tube.
Replace power supply
Is the drinking fountain not getting power, and have you ruled out the cable and adapter? Then replace the power supply.
Replace UV lamp
How to replace the UV lamp in the Hydrate Ultra.
Replace main circuit board
In this video, you will see step by step how to replace the main circuit board. First, remove the plug from the socket.
Replace second printed circuit board
This is how you replace the second circuit board of the Hydrate Ultra. First, unplug the power cord from the outlet.